Effects of thickness and background on the masking ability of high -trasnlucent zirconias

Purpose@#The purpose of this study was to compare and evaluate the masking ability of three types of high translucent zirconia according to the various thicknesses and backgrounds. @*Materials and Methods@#Using three types of high-translucency zirconia (Ceramill zolid fx white, Ceramill zolid ht+ white, Ceramill zolid ht+ preshade A2), 10 cylindrical specimens were fabricated in 10mm diameter and each with four thicknesses (0.6 mm, 1.0 mm, 1.5 mm, 2.0 mm), respectively by CAD/CAM method. The background was 10 mm in diameter and 10 mm in thickness. A1, A2, A3 flowable resin backgrounds, blue-colored core resin background, and Ni-Cr alloy background were prepared, and black, white backgrounds provided by the spectrophotometer manufacturer (x-rite, Koblach, Austria) were used. zirconia specimens and the background specimen were stacked to measure L, a*, b* with Spectrophotometer (Color i5, x-rite, Koblach, Austria) and the ∆E value with the other background is calculated. The Calculated mean ∆E values were compared based on perceptibility threshold 1.0 and acceptability threshold 3.7. Nonparametric tests such as Kruskal-Wallis test were performed to verify statistical significance (α = 0.05). @*Results@#There was a significant difference in the mean ∆E value according to the zirconia type, background and thickness change (P = 0.000). @*Conclusion@#According to the results of this study, the pre-colored high-translucent zirconia can obtain the desired zirconia shade when it is restored on teeth, composite resins, and abutments except for the blue resin core.

Tensile bond strength of chairside reline resin to denture bases fabricated by subtractive and additive manufacturing / 대한치과보철학회지

Purpose@#The purpose of this study was to compare and evaluate the tensile bond strength of chairside reline resin to denture base resin fabricated by different methods (subtractive manufacturing, additive manufacturing, and conventional heat-curing). @*Materials and methods@#Denture base specimens were fabricated as cuboid specimens with a width of 25 mm × length 25 mm × height 3 mm by subtractive manufacturing (VITA VIONIC BASE), additive manufacturing (NextDent Base) and conventional heat-curing (Lucitone 199). After storing the specimens in distilled water at 37°C for 30 days and drying them, they were relined with polyethyl methacrylate (PEMA) chairside reline resin (REBASE II Normal). The subtractive and additive manufacturing groups were set as the experimental group, and the heat-curing group was set as the control group. Ten specimens were prepared for each group. After storing all bound specimens in distilled water at 37°C for 24 hours, the tensile bond strength between denture bases and chairside reline resin was measured by a universal testing machine at a crosshead speed of 10 mm/min. The fracture pattern of each specimen was analyzed and classified into adhesive failure, cohesive failure, and mixed failure. Tensile bond strength, according to the fabrication method, was analyzed by 1-way ANOVA and Bonferroni’s method (α =.05). @*Results@#Mean tensile bond strength of the heat-curing group (2.45 ± 0.39 MPa) and subtractive manufacturing group (2.33 ± 0.39 MPa) had no significant difference (P>.999). The additive manufacturing group showed significantly lower tensile bond strength (1.23 ± 0.36 MPa) compared to the other groups (P<.001). Most specimens of heat-curing and subtractive manufacturing groups had mixed failure, but mixed failure and adhesive failure showed the same frequency in additive manufacturing group. @*Conclusion@#The mean tensile bond strength of the subtractive manufacturing group was not significantly different from the heat-curing group. The additive manufacturing group showed significantly lower mean tensile bond strength than the other two groups.

Marginal and internal fit of 3D printed provisional crowns according to build directions

PURPOSE@#. This study aimed to fabricate provisional crowns at varying build directions using the digital light processing (DLP)-based 3D printing and evaluate the marginal and internal fit of the provisional crowns using the silicone replica technique (SRT). MATERIALS AND METHODS. The prepared resin tooth was scanned and a single crown was designed using computer-aided design (CAD) software. Provisional crowns were printed usinga DLP-based 3D printer at 6 directions (120°, 135°, 150°, 180°, 210°, 225°) with 10 crowns in each direction. In total, sixty crowns were printed. To measure the marginal and internal fit, a silicone replica was fabricated and the thickness of the silicone impression material was measured using a digital microscope. Sixteen reference points were set and divided into the following 4 groups: marginal gap (MG), cervical gap (CG), axial gap (AG),and occlusal gap (OG). The measurements were statistically analyzed using one-way ANOVA and Dunnett T3. @*RESULTS@#MG, CG, and OG were significantly different by build angle groups (P<.05). The MG and CG were significantly larger in the 120° group than in other groups. OG was the smallest in the 150° and 180° and the largest in the 120° and 135° groups. @*CONCLUSION@#The marginal and internal fit of the 3D-printed provisional crowns can vary depending on the build angle and the best fit was achieved with build angles of 150°and 180°

Clinical study on screw loosening in dental implant prostheses: a 6-year retrospective study

Objectives@#In this study, we determined the incidence and pattern of screw loosening in patients who received dental implants. @*Materials and Methods@#Patients who received implants between January 2008 and October 2013 and completed their prosthetic rehabilitation were evaluated for the incidence, frequency, and onset of screw loosening using dental charts and radiographs. The association between each factor and screw loosening was analyzed using the chi-square test and a multivariate analysis with binary logistic regression models (P<0.05). @*Results@#Total 1,928 implants were placed in 837 patients (448 males, 389 females), whose follow-up period after loading varied from 0.25 to 70 months (mean period, 31.5 months). Screw loosening occurred in 7.2% of implants. Most cases occurred less than six months after loading. Among those, 22.3% experienced recurrent screw loosening. Screw loosening was most common in the molar region (8.5%) and frequently associated with an implant diameter of ≥5 mm (14.2%). External implant–abutment connections (8.9%) and screw-retained implant prostheses (10.1%) showed higher incidence of problems than internal implant–abutment connections and cement-retained implants, respectively. Screw loosening was most common in implant prostheses with single crowns (14.0%). @*Conclusion@#Within the limits of the current study, we conclude that the incidence of screw loosening differs significantly according to the position of implant placement, the type of implant and manufacturer, implant diameter, the type of implant–abutment connection, the type of retention in the implant prosthesis, and the type of implant prosthesis.

Comparison of marginal and internal discrepancies of zirconia crowns fabricated by various digital scan methods / 대한치과재료학회지

In this study, marginal and internal discrepancies of zirconia crowns fabricated with the CAD/CAM (computer aided design

Comparative evaluation of marginal and internal fit of metal copings fabricated by various CAD/CAM methods / 대한치과보철학회지

PURPOSE: The purpose of the present study was to compare the accuracy of four different metal copings fabricated by CAD/CAM technology and to evaluate clinical effectiveness. MATERIALS AND METHODS: Composite resin tooth of the maxillary central incisor was prepared for a metal ceramic crown and duplicated metal die was fabricated. Then scan the metal die for 12 times to obtain STL files using a confocal microscopy type oral scanner. Metal copings with a thickness of 0.5 mm and a cement space of 50 µm were designed on a CAD program. The Co-Cr metal copings were fabricated by the following four methods: Wax pattern milling & Casting (WM), Resin pattern 3D Printing & casting (RP), Milling & Sintering (MS), Selective laser melting (SLM). Silicone replica technique was used to measure marginal and internal discrepancies. The data was statistically analyzed with One-way analysis of variance and appropriate post hoc test (Scheffe test) (α=.05). RESULTS: Mean marginal discrepancy was significantly smaller in the Group WM (27.66 ± 9.85 µm) and Group MS (28.88 ± 10.13 µm) than in the Group RP (38.09 ± 11.14 µm). Mean cervical discrepancy was significantly smaller in the Group MS than in the Group RP. Mean axial discrepancy was significantly smaller in the Group WM and Group MS then in the Group RP and Group SLM. Mean incisal discrepancies was significantly smaller in the Group RP than in all other groups. CONCLUSION: The marginal and axial discrepancies of the Co-Cr coping fabricated by the Wax pattern milling and Milling/Sintering method were better than those of the other groups. The marginal, cervical and axial fit of Co-Cr copings in all groups are within a clinically acceptable range.

Association between Green Tea Consumption and Sarcopenia in Menopausal Women: a Cross Sectional Analysis of the Korea National Health and Nutrition Examination Survey 2008-2011

BACKGROUND: Many studies of the effect of catechins, a major substance in green tea, on sarcopenia have been conducted using animal models or as in vitro experiments, revealing that they increase muscle mass, inhibit proteases, and promote satellite cell proliferation. No study has been conducted targeting human subjects relative to the correlation between green tea and sarcopenia. The purpose of this study was to investigate the correlation between green tea intake and sarcopenia in menopausal women using the Korea National Health and Nutrition Examination Survey (2008–2011).METHODS: This study included 3,473 menopausal women after excluding those diagnosed with gastric cancer and other cancers. The frequency of green tea intake was determined based on the Food Frequency Questionnaire, and the value acquired from calibrating the extremity muscle mass measured using dual-energy X-ray absorptiometry with weight was used as the muscle mass. Sarcopenia was defined using values less than two standard deviations as cut-offs after determining the mean and standard deviation of the muscle mass in the group of young and healthy women.RESULTS: In menopausal women, the odds ratio of the group drinking a cup or less and two or more cups of green tea to that of the group not drinking green tea was 1.170 (0.891–1.536), and the 95% confidence interval was 1.530 (0.744–3.146). A significant linear trend was not observed in the result (P for trend 0.148).CONCLUSION: There was no significant correlation between green tea intake and sarcopenia in menopausal women in Korea.

Comparison of Three-Dimensional Accuracy between Digital Models Obtained from Impression Scan and Model Scan / 대한치과재료학회지

The purpose of the study is to compare and analyze the accuracy of digital images obtained from impression and stone model with model scanner and to find out clinical effectiveness. A mandibular left first molar composite resin tooth was made for abutment. Digital models were obtained with a same model scanner(Ceramill Map 400, Amann Girrbach, Austria); (1) Fabricated resin model was scanned(Group C). (2) 10 impressions were taken with putty and polyvinyl siloxane, then were scanned (Group I). (3) Type IV stone was poured in each impressions made in step(2) and 10 stone models were scanned(Group S). 3 dimensional super-impositional program (Geomagic control X, 3D Systems, USA) was used to analyze the STL files. Stone model scan(Group S) showed lower deviation than impression scan(Group I) compared to the control group(P < 0.001). Both Group I and Group S showed signs of expansion in the occlusion surface and margin surface while showing contraction in the axial surface. The deviations were smaller in order of occlusal plane, horizontal plane of margin and axial plane. Within the limited boundary of this study, the digital model obtained from stone model scan showed smaller deviation than the digital model obtained from impression scan.

Associations between Breast Density on Mammography and Lifestyle Related Disease

BACKGROUND: Dense breast reduced the sensitivity of mammography in breast cancer screening and known as an independent risk factor of breast cancer. The relationship between breast density and age, body mass index has studied. However, there are few studies on the relationship between breast density and lifestyle related disease. In this study, we investigated the relationship between mammographic breast density and lifestyle related disease. METHODS: Retrospective cross sectional research was carried out from people who visited a single health screening center in Busan from January 2015 to December 2015. We investigated age, past history of the subjects and measured their height, weight, blood pressure and waist circumference. The biochemical test was carried out using their blood. All patients underwent mammography. The breast density on mammography determined by the basis of American College of Radiology Breast Imaging Reporting and Data System (ACR BI-RADS) breast composition and 996 people was recruited. RESULTS: In the distribution of breast density, 16.3% of women (n=160) had dense breast. Age (under 49), body mass index (BMI) (underweight) were positively correlated with the BI-RADS composition category 3, 4 but the number of lifestyle related disease were negatively correlated (age ρ=0.17, BMI ρ=0.39, the number of lifestyle related disease ρ=-0.21). The odds ratio (OR) of dense breast increased with decreasing lifestyle related disease severity (OR=3.06, 95% confidence interval: 1.13-8.22, P=0.027). CONCLUSIONS: This study showed that the number of lifestyle related disease was negatively correlated with mammographic density. The OR of dense breast increased with decreasing lifestyle related disease severity. Therefore, primary physicians should consider negative correlation between breast density and lifestyle related disease in breast cancer screening.

Retrospective study on marginal bone loss around maxillary anterior implants with or without bone graft / 대한치과보철학회지

PURPOSE: This study is to evaluate the clinical significance of implantation with simultaneous bone graft by comparing the marginal bone loss around maxillary anterior implants with or without bone graft MATERIALS AND METHODS: Patients treated with implant-retained restorations on maxillary anterior region at Implant Center, Dental Hospital, Wonkwang University between June 2011 and May 2014 were included in this study. Date of implant placement, implant diameter, implant length, implant-abutment connection type and whether the bone graft was done were investigated. The patient's periapical radiographs taken immediately after implantation and at the most recent visit were compared. Marginal bone loss was measured using Emago advanced v5.6 program (Oral diagnostic systems, Amsterdam, Netherlands). Statistical analysis was done in independent t-test by using SPSS 22.0 program. RESULTS: As a result of observing on 83 implants (without bone graft: 44, with bone graft: 39) of 52 patients for 6 - 45 months (average: 18.4 months), implants without bone graft showed 1.42 ± 0.42 mm, implants with bone graft showed 1.28 ± 0.45 mm of marginal bone loss. CONCLUSION: In limitations of this study, implants with simultaneous bone graft had significantly less marginal bone loss than implants without bone graft.

Mouth rehabilitation of a patient with severely worn dentition with vertical dimension increase / 대한치과보철학회지

Treating patients with severely worn dentition often requires comprehensive prosthetic treatments. Oral rehabilitation and long-term stability could be achieved by analyzing the cause of the wear and changing vertical dimension. The temporary restoration procedure is executed and patient's adaptation is evaluated by long-term observation when treatment is accompanied with increasing vertical dimension. In this case, 54 year-old male presented with worn dentition and esthetic dissatisfaction. In oral manifestations, severely worn dentition with attrition and erosion is diagnosed. To evaluate change of vertical dimension, interocclusal rest space, facial appearance, pronunciation, clinical crown length, distance from incisor edge to labial vestibule are evaluated. Consequently, 2.5 mm increase of vertical dimension that based on articulator incisal pin is determined. After 8 weeks stabilization period with temporary prostheses, definitive prostheses are fabricated. After 6 months follow up period, satisfactory outcomes were achieved both in functional and esthetic aspects through this procedure.

The influence of surface conditioning on the shear bond strength of self-adhesive resin cement to zirconia ceramics / 대한치과보철학회지

PURPOSE: To evaluate the effect of surface conditioning on the shear bond strength of zirconium-oxide ceramic to 4 luting agents. MATERIAL AND METHODS: A total of 120 disk-shaped zirconium-oxide ceramic blocks (3Y-TZP, Kyoritsu, Japan) were treated as follows: (1) Sandblasting with 110 microm aluminum-oxide (Al2O3) particles; (2) tribochemical silica coating (Rocatec) using 110 microm Al2O3 particles modified by silica; (3) no treatment. Then zirconium-oxide ceramic blocks bonded with 4 luting cements (RelyX luting (3M ESPE), Maxcem (Kerr), Nexus3 (Kerr), Rely X Unicem (3M ESPE)). Each group was tested in shear bond strengths by UTM. A 1-way analysis of variance and 2-way analysis of variance was used to analyze the data (alpha = .05). RESULTS: RelyX unicem in combination tribochemical silica-coating produced a highest bond strength (P < .05). Air abrasion group and Rocatec treatment groups resulted in significantly higher than no conditioning group (P < .05). RelyX Luting groups showed lower bond strength than other groups. There were significant differences among groups (P < .05). CONCLUSION: Within the limitation of this study, RelyX Unicem cement provided the highest bond strength and Rocatec treatment enhanced the bond strength.

The fracture resistance of heat pressed ceramics with wire reinforcement / 대한치과보철학회지

STATEMENT OF PROBLEM: Ceramics have been important materials for the restoration of teeth. The demands of patients for tooth-colored restorations and the availability of various dental ceramics has driven the increased use of new types of dental ceramic materials. Improved physical properties of theses materials have expanded its use even in posterior crowns and fixed partial dentures. However, ceramic still has limitation such as low loading capability. This is critical for long-span bridge, because bridge is more subject to tensile force. PURPOSE: The wire reinforced ceramic was designed to increase the fracture resistance of ceramic restoration. The purpose of this study was to evaluate the fracture resistance of wire reinforced ceramic. MATERIAL AND METHODS: Heat pressed ceramic (ingot No.200 : IPS Empress 2, Ivoclar Vivadent, Liechtenstein) and Ni-Cr wire (Alfa Aesar, Johnson Matthey Company, USA) of 0.41 mm diameter were used in this study. Five groups of twelve uniform sized ceramic specimens (width 4 mm, thickness 2 mm, length 15 mm) were fabricated. Each group had different wire arrangement. Wireless ceramic was used as control group. The experimental groups were divided according to wire number and position. One, two and three strands of wires were positioned on the longitudinal axis of specimen. In another experimental group, three strands of wires positioned on the longitudinal axis and five strands of wires positioned on the transverse axis. Three-point bending test was done with universal testing machine (Z020, Zwick, Germany) to compare the flexural modulus, flexural strength, strain at fracture and fracture toughness of each group. Fractured ceramic specimens were cross-sectioned with caborundum disc and grinded with sandpaper to observe interface between ceramic and Ni-Cr wire. The interface between ceramic and Ni-Cr wire was analyzed with scanning electron microscope (JSM-6360, JEOL, Japan) under platinum coating. RESULTS: The results obtained were as follows: 1. The average and standard deviation in flexural modulus, flexural strength and fracture toughness showed no statistical differences between control and experimental groups. However, strain was significantly increased in wire inserted ceramics (P < .001). 2. Control group showed wedge fracture aspects across specimen, while experimental groups showed cracks across specimen. 3. Scanning electron microscopic image of cross-sectioned and longitudinally-sectioned specimens showed no gap at the interface between ceramic and Ni-Cr wire. CONCLUSION: The results of this study showed that wire inserted ceramics have a high strain characteristic. However, wire inserted ceramics was not enough to use at posterior area of mouth in relation to flexural modulus and flexural strength. Therefore, we need further studies.

Fitness of Adjustable Dental Impression Trays on the Caucasian and African American / 대한치과보철학회지

PURPOSE: This study was designed to investigate the fitness of adjustable dental impression trays on the Caucasian and African American. MATERIAL AND METHODS: The size and shape of these trays were designed from the results of the dental arch size of Korean adults. Tray samples were made by CAD-CAM working. Sixty Caucasian (male: 30, female: 30) and sixty African American (male: 30, female: 30) were selected for taking irreversible hydrocolloid impression using these trays. The author measured the width and length of impression material on the several measuring points. RESULTS: 1. Uniform impression material width was achieved by controling the width of the tray using stops and beveled guides. 2. In the maxillary tray on the Caucasian, the impression material thickness was measured to be rather great showing thickness of the midpalatal part 13.0 mm. 3. In the maxillary tray on the African American, the impression material thickness was measured to be rather great showing thickness of the midpalatal part 12.0 mm, posterior palatal part 11.0 mm and the labial frenum width was 11.0 mm. 4. In the maxillary tray on the African American, the impression material width of posterior border (0.8 mm) was measured to be small. 5. In the mandibular tray on the Caucasian, the impression material width was measured (2.7-6.7 mm) and posterior border width (2.1 mm) was measured small. The impression material length was measured (2.8-6.7 mm). 6. In the mandibular tray on the African American, the impression material width was measured to be rather great showing width of the labial frenum 9.2 mm and the width of posterior border was measured too small (0.3 mm). CONCLUSION: This adjustable dental tray shows good accuracy to Korean because it was designed by the analysis of the dental arch size of Korean adult model. With this result, it can be applied to Caucasian and African American, we can take more easy and accurate dental impressions.

Photoelastic stress analysis of implants according to fixture design / 대한치과보철학회지

PURPOSE: The purpose of this study was to evaluate the pattern and the magnitude of stress distribution in the supporting tissues surrounding three different types of implants(ITI, 3i, and Bicon implant system). MATERIAL AND METHOD: Photoelastic models were made with PL-2 resin(Measurements Group, Raleigh, USA) and three implants of each kind were placed in the mandibular posterior edentulous area distal to the canine . For non-splinted restorations, individual crowns were fabricated on three titanium abutments. For splinted restorations, 3-unit fixed partial dentures were fabricated. Photoelastic stress analyses were carried out to measure the fringe order around the implant supporting structure under simulated loaded conditions(15 lb, 30 lb). CONCLUSION: The results were as follows; 1. Regardless of the implant design, stresses were increased in the apex region of loaded implant when non-splinted restorations were loaded. While relatively even stress distribution occurred with splinted restorations. Splinting was effective in the second implant. 2. Strain around Bicon implant were lower than those of other implants, which confirmed the splinting effect. The higher the load, the more the stress occurred in supporting tissue, which was most obvious in the Bicon system. 3. Stress distribution in the supporting tissue was favorable in the ITI system, while the other side of 3i system tended to concentrate the stress in some parts.

Photoelastic stress analysis of implants according to fixture design / 대한치과보철학회지

PURPOSE: The purpose of this study was to evaluate the pattern and the magnitude of stress distribution in the supporting tissues surrounding three different types of implants(ITI, 3i, and Bicon implant system). MATERIAL AND METHOD: Photoelastic models were made with PL-2 resin(Measurements Group, Raleigh, USA) and three implants of each kind were placed in the mandibular posterior edentulous area distal to the canine . For non-splinted restorations, individual crowns were fabricated on three titanium abutments. For splinted restorations, 3-unit fixed partial dentures were fabricated. Photoelastic stress analyses were carried out to measure the fringe order around the implant supporting structure under simulated loaded conditions(15 lb, 30 lb). CONCLUSION: The results were as follows; 1. Regardless of the implant design, stresses were increased in the apex region of loaded implant when non-splinted restorations were loaded. While relatively even stress distribution occurred with splinted restorations. Splinting was effective in the second implant. 2. Strain around Bicon implant were lower than those of other implants, which confirmed the splinting effect. The higher the load, the more the stress occurred in supporting tissue, which was most obvious in the Bicon system. 3. Stress distribution in the supporting tissue was favorable in the ITI system, while the other side of 3i system tended to concentrate the stress in some parts.

Three dimensional finite element analysis of internally connected implant systems / 대한치과보철학회지

STATEMENT OF PROBLEM: Currently, there are some 20 different geometric variations in implant/abutment interface available. The geometry is important because it is one of the primary determinants of joint strength, joint stability, locational and rotational stability. PURPOSE: As the effects of the various implant-abutment connections and the prosthesis height variation on stress distribution are not yet examined, this study is to focus on the different types of implant-abutment connection and the prosthesis height using three dimensional finite element analysis. MATERIAL AND METHOD: The models were constructed with ITI, 3i TG, Bicon, Frialit-2 fixtures and solid abutment, TG post, Bicon post, EstheticBase abutment respectively. And the superstructures were constructed as mandibular second premolar shapes with 8.5 mm, 11 mm, 13.5 mm of crown height. In each model, 244 N of vertical load and 244 N of 30 degree oblique load were placed on the central pit of an occlusal surface. von Mises stresses were recorded and compared in the crowns, abutments, fixtures. RESULTS: 1. Under the oblique loading, von Mises stresses were larger in the crown, abutment, fixture compared to the vertical loading condition. 2. The stresses were increased proportionally to the crown height under oblique loading but showed little differences with three different crown heights under vertical loading. 3. In the crown, the highest stress areas were loading points under vertical loading, and the finish lines under oblique loading. 4. Under the oblique loading, the higher stresses were located in the fixture/abutment interface of the Bicon and Frialit-2 systems compared to the ITI and TG systems. CONCLUSIONS: The stress distribution patterns of each implant-abutment system had difference among them and adequate crown height/implant ratio was important to reduce the stresses around the implants.

Three dimensional finite element analysis of internally connected implant systems / 대한치과보철학회지

STATEMENT OF PROBLEM: Currently, there are some 20 different geometric variations in implant/abutment interface available. The geometry is important because it is one of the primary determinants of joint strength, joint stability, locational and rotational stability. PURPOSE: As the effects of the various implant-abutment connections and the prosthesis height variation on stress distribution are not yet examined, this study is to focus on the different types of implant-abutment connection and the prosthesis height using three dimensional finite element analysis. MATERIAL AND METHOD: The models were constructed with ITI, 3i TG, Bicon, Frialit-2 fixtures and solid abutment, TG post, Bicon post, EstheticBase abutment respectively. And the superstructures were constructed as mandibular second premolar shapes with 8.5 mm, 11 mm, 13.5 mm of crown height. In each model, 244 N of vertical load and 244 N of 30 degree oblique load were placed on the central pit of an occlusal surface. von Mises stresses were recorded and compared in the crowns, abutments, fixtures. RESULTS: 1. Under the oblique loading, von Mises stresses were larger in the crown, abutment, fixture compared to the vertical loading condition. 2. The stresses were increased proportionally to the crown height under oblique loading but showed little differences with three different crown heights under vertical loading. 3. In the crown, the highest stress areas were loading points under vertical loading, and the finish lines under oblique loading. 4. Under the oblique loading, the higher stresses were located in the fixture/abutment interface of the Bicon and Frialit-2 systems compared to the ITI and TG systems. CONCLUSIONS: The stress distribution patterns of each implant-abutment system had difference among them and adequate crown height/implant ratio was important to reduce the stresses around the implants.

A study on the illumination of dental clinic / 대한치과보철학회지

Purpose: This study was designed to investigate the present conditions of illumination techniques in dental clinics in order to contribute improvement of operating environment. This study also aimed exploring qualitative and quantitative luminous intensity required for color temperature in dental clinic illumination, which was a critical part of esthetic dentistry. Materials and methods: A total of forty-eight local dental clinics were selected for sampling a) luminous intensity, and b) color temperature. The author measured the luminous intensity and the color temperature with lux meter and color meter respectively between 12pm and 2pm. The dental unit chair placed in the general operation positions were kept the distance 60 cm, then all dental units were measured three times and averaged. The author measured the luminous intensity and color temperature with both common dental operating light and then without operating light in different office environments. The study was conducted under three conditions: 1. artificial illumination in clear day light 2. artificial illumination in cloudy day light, and 3. artificial illumination alone. Results: The results obtained were as follows. 1. The average luminous intensity in dental clinic lighting was 425 lux which was not sufficient to produce the optimal shade of the patient's teeth. Furthermore, the average luminous intensity even in full operating lighting was 9532 lux which fell short of the required level of 10,000 lux. 2. The average color temperature of all dental clinics surveyed was 5169 K which met the optimal range. However, only 33.3% fell in the correct region between 5,000-5,500 K as 25% were over 5,500 K and 41.6% were below 5,000 K. As a result, 66.7% were under insufficient color temperature conditions. 3. The dental unit chair placed next to a window, hence exposure to natural lighting, had significantly higher luminous intensity and color temperature compared to the dental unit chair which didn't have a window or natural lighting. 4. The data analysis revealed that only 6.3% of the dental clinic were met the standard of the average luminous intensity and color temperature.

A Case of Type 1 von Hippel-Lindau (VHL) Disease associated with VHL Germline Mutation / 대한내분비학회지

Von Hippel-Lindau (VHL) disease is an autosomal dominant neoplasia syndrome that result from a germline mutation in the VHL gene. Germline mutation in the VHL gene lead to the development of hemangioblastomas of the central nervous system and retina, cysts and clear cell carcinoma of the kidney, cyst adenomas of other organs, and pheochromocytoma. VHL is a tumor suppressor gene on the short arm of chromosome 3. VHL disease has been classified into two main clinical subtypes depending on the presence (type 2) or absence (type 1) of pheochromocytoma. Type 2 has been subdivided into three categories depending on the presence (type 2B) or absence (type 2A) of renal cell carcinoma, with type 2C being a rare subtype in which pheochromocytoma is the sole manifestation of VHL disease. Recently we experienced a family with VHL type 1 who carry C to T (Q73X) transition in codon 217 nonsense germline mutation in exon 1 of VHL gene. The authors report this case with literature review.